d1u-w-1600-48-hx.b04 page of 4 d1u-w-1600-48-hx series ac/dc front end power supply p o w e r e l e c t r o n i c s d i v i s i o n a c / d c p o w e r s u p p l i e s www.cd4power.com technical enquiries email: toronto@cdtechno.com, tel: (866) 740 232 features n rohs compliant n 600w (220vac), 200w ( 0vac) output power n 48v main output, 3.3v, 5v or 2v standby output n u sized; dimensions 2 x 4.75 x .6 n 7.5 watts per cubic inch density n n+ redundancy capable, including hot-docking n active current sharing on main output n over-voltage, over-current, over-temperature protection n internal cooling fans n i2c bus interface with status indicators n optional u x 9 power-shelf description the d u-w-600 is a 600 watt, power-factor- corrected (pfc) front-end power supply for hot-swapping redundant systems. the main output is 48v and standby output of either 2v, 5v or 3.3v. packaged in u low profle, it is designed to deliver reliable bulk power to servers, workstations, storage systems or any 48v distributed power architecture systems requiring high power density. the highly effcient electrical and thermal design with internal cooling fans supports reliable operation conditions. the d u-w-600 is designed to auto-recover from over-current and over-temperature faults. status information is provided with front panel leds, logic signals and i 2 c management interface. three units can be packaged into an optional 9 u power shelf to provide up to 4.8kw of power. selection guide model number power output high line ac power output low line ac main output standby output airfow d u-w-600-48-hc2c 600w 200w 48v 3.3v back to front d u-w-600-48-ha2c 600w 200w 48v 5v back to front d u-w-600-48-hb2c 600w 200w 48v 2v back to front d u-w-600-48-hcc 600w 200w 48v 3.3v front to back d u-w-600-48-hac 600w 200w 48v 5v front to back d u-w-600-48-hbc 600w 200w 48v 2v front to back input characteristics parameter conditions min. typ. max. units input voltage operating range 90 264 vac input frequency 47 55 63 hz turn-on input voltage ramp up 78.5 86.5 vac turn-off input voltage ramp down 70.5 78 maximum input current 5 arms inrush current 90 apk output voltage characteristics output voltage parameter conditions min. typ. max. units 48v voltage set point accuracy 48 vdc line and load regulation 46.54 49.44 ripple voltage & noise 20mhz bandwidth 480 mv p-p output current 2 33 a 3.3vsb voltage set point accuracy 3.3 vdc line and load regulation 3.2 3.4 ripple voltage & noise 50 mv p-p operating range 0 4.5 a 5vsb voltage set point accuracy 5 vdc line and load regulation 4.85 5.5 ripple voltage & noise 50 mv p-p operating range 0 4 a 2vsb voltage set point accuracy 2 vdc line and load regulation .2 2.4 ripple voltage & noise 20 mv p-p operating range 0 .7 a output characteristics parameter conditions min. typ. max. units remote sense 240 mv effciency 220vac 90.6 % start-up time ac ramp up .5 s ps_on activated 50 ms transient response 48v ramp a/s 2700 mv 2vsb ramp a/s 600 5vsb ramp a/s 250 3.3vsb ramp a/s 65 current sharing accuracy (up to 3 in parallel) at 00% load 0 % hold-up time 20 ms ripple and noise are measured with 0. uf of ceramic capacitance and 0 uf of tantalum capacitance on each of the power supply outputs. the output noise requirements apply over a 0 hz to 20 mhz bandwidth. a short coaxial cable with 50ohm scope termination is used.
d1u-w-1600-48-hx.b04 page 2 of 4 d1u-w-1600-48-hx series ac/dc front end power supply p o w e r e l e c t r o n i c s d i v i s i o n a c / d c p o w e r s u p p l i e s www.cd4power.com technical enquiries email: toronto@cdtechno.com, tel: (866) 740 232 general characteristics parameter conditions min. typ. max. units storage temperature range non-condensing -40 25 c operating temperature range 0 50 operating humidity non-condensing 0 90 % storage humidity 5 90 shock 30g non operating sinusoidal vibration 0.5g, 5 C 500 hz mtbf calculated per bellcore at ta=30 c 200 khrs demonstrated 200 khrs safety approvals c-csa-us (csa 60950--03/ul 60950- , first edition) protection characteristics output voltage parameter conditions min. typ. max. units over-temperature auto-restart 55 65 c 48v over voltage latching 54 59 v over current latching 37 42 a 2vsb over voltage latching 3 4 v over current latching 2.5 3 a 3.3vsb over voltage latching 3.57 4.02 v over current latching 6.5 8 a 5vsb over voltage latching 5.6 6 v over current latching 4.4 6 a isolation characteristics parameter conditions min. typ. max. units insulation safety rating / test voltage input to output - reinforced 3000 vrms input to chassis - basic 500 vrms isolation output to chassis output to output material flammability ul 94v-0 control signals status conditions description led off no ac input to all ps flashing yellow power supply failure flashing green main output absent green power supply good
d1u-w-1600-48-hx.b04 page 3 of 4 d1u-w-1600-48-hx series ac/dc front end power supply p o w e r e l e c t r o n i c s d i v i s i o n a c / d c p o w e r s u p p l i e s www.cd4power.com technical enquiries email: toronto@cdtechno.com, tel: (866) 740 232 output connector and signal specification dc and signal connector: tyco part # -6450332-7, or fci powerblade # 5 732-028 pin assignment signal name description high level low level i max p , p2, p3 v out main output voltage p4, p5, p6 v rtn main output voltage, return a2 v sense + v out remote sense, positive node input a3 v sense - v out remote sense, negative node input c2, c3, d3 v_ sb standby voltage output c4, c5, d4, d5 v_ sb return standby voltage, return b i_share active load sharing bus 0 C 8v -4 ma / +5 ma d ac_ok input ac voltage ok signal output (internal pull up is 0k? to vsb for the 3.3v/5v aux. models and 0k? to 5v for the 2v aux. model) >2.4v (active, ok) <0.4v -2 ma +4 ma d2 p_good power good signal output (internal pull up is 0k? to vsb for the 3.3v/5v aux. models and 0k? to 5v for the 2v aux. model) >2.4v (active, good) <0.4v -2 ma +4 ma a ps_kill floating pin will turn off p/s. vsb tbd ma b5 ps_present internally tied to vsb return 0 v c ps_on internal k ohm pull-up to vsb, (accepts open collector/ drain drive) >2. v (open, or vsb) <0.7v (active, ps:on) - ma -4 ma a4 i 2 c data i 2 c serial data bus vsb a5 i 2 c clock i 2 c serial clock bus vsb b2 i 2 c adr0 address input 0, internal pull-up to vsb >2. v, < vsb <0.8v ma b3 i 2 c adr address input , internal pull-up to vsb >2. v, 2. v, d1u-w-1600-48-hx.b04 page 4 of 4 d1u-w-1600-48-hx series ac/dc front end power supply p o w e r e l e c t r o n i c s d i v i s i o n a c / d c p o w e r s u p p l i e s www.cd4power.com technical enquiries email: toronto@cdtechno.com, tel: (866) 740 232 mechanical dimensions dimensions: 2.00l x 4.75 w x .6 h (40.7h x 20.6w x 304.90mm) d1u mating connectors 48v d u mating connector press fit solder 2 straight right angle straight right angle c&d n/a pending n/a 36-0430032-0 fci 5742-0602000calf 5762-0602000cblf 5742-0602000aalf 5762-0602000ablf tyco tbd tbd tbd tbd 2 solder connector recommended for board thickness of <0.090 optional accessories description part number 48v du output connector card du-48-conc 04/7/07 ? 200 7 c&d technologies, inc c&d t echnologies, in c. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. the descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. specifcations are subject to change without notice. c&d technologies, inc. cabot boulevard, mansfeld, ma 0204 8 -5 u.s.a. tel: (508) 339-3000 (800) 233-2765 fax: (508) 339-6356 www.cd4power.com email: sales@cdtechno.com iso 9001 registered ? usa: tucson (az), tel: (800) 547 2537, email: sales@cdtechno.com canada: toronto, tel: (866) 740 232 , email: toronto@cdtechno.com united kingdom: milton keynes, tel: +44 (0) 908 6 5232, email: mk@cdtechno.com france: montigny le bretonneux, tel: +33 (0) 34 60 0 0 , email: france@cdtechno.com germany: mnchen, tel: +49 (0)89-544334-0, email: ped.munich@cdtechno.com japan: tokyo, tel: 3-3779- 03 , email: sales_tokyo@cdtechno.com osaka, tel: 6-6354-2025, e mail: sales_osaka@cdtechno.com website: www.cd4power.jp china: shanghai, tel: +86 2 5 027 3678, email: shanghai@cdtechno.com guangzhou, tel: +86 208 22 8066, email: guangzhou@cdtechno.com 41.00040 [1.6140.015] 20,20 0,40 0.795 0.015 [ ] 127,85 0,40 5.033 0.015 [ ] 304,80 0,65 12.000 0.025 [ ] 12,63 0,40 0.497 0.015 [ ] 312,89 0,35 12.319 0.013 [ ] ref 8,89 0.350 [ ] 132,85 0,50 5.230 0.019 [ ] 120,65 0,65 4.750 0.025 [ ] 37,31 0,40 1.469 0.015 [ ]
|
